Search Results

A method for automatic reduction of detailed reaction mechanisms using simultaneous sensitivity, reaction flow and lifetime analysis has been developed and applied to a two-zone model of an SI engine fuelled with Primary Reference Fuel (PRF). Species which are less relevant for the occurrence of autoignition in the end gas are declared redundant. They are identified and eliminated for different pre-set minimum levels of reaction flow and sensitivity. The resulting skeletal mechanism is valid in the ranges of initial and boundary values for which the analyses have been performed. A measure of species lifetime is calculated from the chemical source terms, and the species with the lifetime shorter than and mass-fraction less than specified limits are selected for removal.

A method for automatic reduction of detailed kinetic to skeletal mechanisms for complex fuels is proposed. The method is based on the simultaneous use of sensitivity and reaction-flow analysis. The resulting skeletal mechanism is valid for the parameter range of initial and boundary values, the analysis have been performed for. The gas-phase chemistry is analyzed in the end gas of an SI-engine, using a two-zone model. Species, not relevant for the occurrence of autoignition in the end gas, are defined as redundant. They are identified and eliminated for different pre-set levels of minimum reaction flow and sensitivity. The error in the mechanism increases monotony with increasing pre-set level of minimum reaction flow.

A zero-dimensional, three-zone model is developed in order to study the gas thermodynamic characteristics and its relation to knock in SI engines. The first zone is the zone behind the flame front, i.e. the burned gas products. The second zone is the unburned gas ahead of the flame front. The end gas adjacent to the wall, in the boundary layer, is not included in the second zone but it is treated as a separate zone, i.e. the third zone. A detailed analysis of the gas thermodynamic state, including heat transfer analysis between the zones and the walls and mass transfer analysis between the zones combined with a detailed chemical kinetic mechanism in each zone have been performed. The effects of piston movement, flame propagation and transient behavior of the thermal boundary layer are modeled. A sudden rise of pressure and temperature and associated heat release in the end gas are calculated if autoignition occurs.

The introduction of a physics-based zero-dimensional stochastic reactor model combined with tabulated chemistry enables the simulation-supported development of future compression-ignited engines. The stochastic reactor model mimics mixture and temperature inhomogeneities induced by turbulence, direct injection and heat transfer. Thus, it is possible to improve the prediction of NOx emissions compared to common mean-value models. To reduce the number of designs to be evaluated during the simulation-based multi-objective optimization, genetic algorithms are proven to be an effective tool. Based on an initial set of designs, the algorithm aims to evolve the designs to find the best parameters for the given constraints and objectives. The extension by response surface models improves the prediction of the best possible Pareto Front, while the time of optimization is kept low.

A simulation method is presented for the analysis of combustion in spark ignition (SI) engines operated at elevated exhaust gas recirculation (EGR) level and employing multiple spark plug technology. The modeling is based on a zero-dimensional (0D) stochastic reactor model for SI engines (SI-SRM). The model is built on a probability density function (PDF) approach for turbulent reactive flows that enables for detailed chemistry consideration. Calculations were carried out for one, two, and three spark plugs. Capability of the SI-SRM to simulate engines with multiple spark plug (multiple ignitions) systems has been verified by comparison to the results from a three-dimensional (3D) computational fluid dynamics (CFD) model. Numerical simulations were carried for part load operating points with 12.5%, 20%, and 25% of EGR. At high load, the engine was operated at knock limit with 0%, and 20% of EGR and different inlet valve closure timing.

In this work are presented experimental and simulated data from a one-cylinder direct injected Diesel engine fuelled with Diesel, two different biodiesel blends and pure biodiesel at one engine operating point. The modeling approach focuses on testing and rating biodiesel surrogate fuel blends by means of combustion and emission behavior. Detailed kinetic mechanisms are adopted to evaluate the fuel-blends performances under both reactor and diesel engine conditions. In the first part of the paper, the experimental engine setup is presented. Thereafter the choice of the surrogate fuel blends, consisting of n-decane, α-methyl-naphtalene and methyl-decanoate, are verified by the help of experiments from the literature. The direct injection stochastic reactor model (DI-SRM) is employed to simulate combustion and engine exhaust emissions (NOx, HC, CO and CO2), which are compared to the experimental data.

In this work a soot source term tabulation strategy for soot predictions under Diesel engine conditions within the zero-dimensional Direct Injection Stochastic Reactor Model (DI-SRM) framework is presented. The DI-SRM accounts for detailed chemistry, in-homogeneities in the combustion chamber and turbulence-chemistry interactions. The existing implementation [1] was extended with a framework facilitating the use of tabulated soot source terms. The implementation allows now for using soot source terms provided by an online chemistry calculation, and for the use of a pre-calculated flamelet soot source term library. Diesel engine calculations were performed using the same detailed kinetic soot model in both configurations. The chemical mechanism for n-heptane used in this work is taken from Zeuch et al. [2] and consists of 121 species and 973 reactions including PAH and thermal NO chemistry. The engine case presented in [1] is used also for this work.

Water injection can be applied to spark ignited gasoline engines to increase the Knock Limit Spark Advance and improve the thermal efficiency. The Knock Limit Spark Advance potential of 6 °CA to 11 °CA is shown by many research groups for EN228 gasoline fuel using experimental and simulation methods. The influence of water is multi-layered since it reduces the in-cylinder temperature by vaporization and higher heat capacity of the fresh gas, it changes the chemical equilibrium in the end gas and increases the ignition delay and decreases the laminar flame speed. The aim of this work is to extend the analysis of water addition to different octane ratings. The simulation method used for the analysis consists of a detailed reaction scheme for gasoline fuels, the Quasi-Dimensional Stochastic Reactor Model and the Detonation Diagram. The detailed reaction scheme is used to create the dual fuel laminar flame speed and combustion chemistry look-up tables.

Methanol is today considered a viable green fuel for combustion engines because of its low soot emissions and the possibility of it being produced in a CO2-neutral manner. Methanol as a fuel for combustion engines have attracted interest throughout history and much research was conducted during the oil crisis in the seventies. In the beginning of the eighties the oil prices began to decrease and interest in methanol declined. This paper presents the emission potential of methanol. T-Φ maps were constructed using a 0-D reactor with constant pressure, temperature and equivalence ratio to show the emission characteristics of methanol. These maps were compared with equivalent maps for diesel fuel. The maps were then complemented with engine simulations using a stochastic reactor model (SRM), which predicts end-gas emissions. The SRM was validated using experimental results from a truck engine running in Partially Premixed Combustion (PPC) mode at medium loads.

Worldwide, there is the demand to reduce harmful emissions from non-road vehicles to fulfill European Stage V+ and VI (2022, 2024) emission legislation. The rules require significant reductions in nitrogen oxides (NOx), methane (CH4) and formaldehyde (CH2O) emissions from non-road vehicles. Compressed natural gas (CNG) engines with appropriate exhaust aftertreatment systems such as three-way catalytic converter (TWC) can meet these regulations. An issue remains for reducing emissions during the engine cold start where the CNG engine and TWC yet do not reach their optimum operating conditions. The resulting complexity of engine and catalyst calibration can be efficiently supported by numerical models. Hence, it is required to develop accurate simulation models which can predict cold start emissions. This work presents a real-time engine model for transient engine-out emission prediction using tabulated chemistry for CNG.

Spray modeling is among the main aspects of mixture formation and combustion in internal combustion engines. It plays a major role in pollutant formation and energy efficiency although adequate modeling is still under development. Strong grid dependence is observed in the droplet-based stochastic spray model commonly used. As an alternative, an interactive model called 'SprayLet' is being developed for spray simulations based on one-dimensional integrated equations for the gas and liquid phases, resulting from cross-sectionally averaging of multi-dimensional transport equations to improve statistical convergence. The formulated one-dimensional cross-section averaged system is solved independently of the CFD program to provide source terms for mass, momentum and heat transfer between the gas and liquid phases. The transport processes take place in a given spray cone where the nozzle exit is automatically resolved.

In more or less all aspects of life and in all sectors, there is a generalized global demand to reduce greenhouse gas (GHG) emissions, leading to the tightening and expansion of existing emissions regulations. Currently, non-road engines manufacturers are facing updates such as, among others, US Tier 5 (2028), European Stage V (2019/2020), and China Non-Road Stage IV (in phases between 2023 and 2026). For on-road applications, updates of Euro VII (2025), China VI (2021), and California Low NOx Program (2024) are planned. These new laws demand significant reductions in nitrogen oxides (NOx) and particulate matter (PM) emissions from heavy-duty vehicles. When equipped with an appropriate exhaust aftertreatment system, natural gas engines are a promising technology to meet the new emission standards.

A model based on an ionization equilibrium analysis, that can relate the ion current to the state of the gas inside the combustion volume, has been presented earlier. This paper introduces several additional models, that together with the previous model have the purpose of improving the pressure predictions. One of the models is a chemistry model that enables us to realistically consider the current contribution from the most relevant species. A second model can predict the crank angle of the peak pressure and thereby substantially increase the accuracy of the pressure predictions. Several other additions and improvements have been introduced, including support for part load engine conditions.

The use of complex reaction schemes is accompanied by high computational cost in 3D CFD simulations but is particularly important to predict pollutant emissions in internal combustion engine simulations. One solution to tackle this problem is to solve the chemistry prior the CFD run and store the chemistry information in look-up tables. The approach presented combines pre-tabulated progress variable-based source terms for auto-ignition as well as soot and NOx source terms for emission predictions. The method is coupled to the 3D CFD code CONVERGE v2.4 via user-coding and tested over various speed and load passenger-car Diesel engine conditions. This work includes the comparison between the combustion progress variable (CPV) model and the online chemistry solver in CONVERGE 2.4. Both models are compared by means of combustion and emission parameters. A detailed n-decane/α-methyl-naphthalene mechanism, comprising 189 species, is used for both online and tabulated chemistry simulations.

In contrast to the currently primarily used liquid fuels (diesel and gasoline), methane (CH4) as a fuel offers a high potential for a significant reduction of greenhouse gas emissions (GHG). This advantage can only be used if tailpipe CH4 emissions are reduced to a minimum, since the GHG impact of CH4 in the atmosphere is higher than that of carbon dioxide (CO2). Three-way catalysts (TWC - stoichiometric combustion) and methane oxidation catalysts (MOC - lean combustion) can be used for post-engine CH4 oxidation. Both technologies allow for a nearly complete CH4 conversion to CO2 and water at sufficiently high exhaust temperatures (above the light-off temperature of the catalysts). However, CH4 combustion is facing a huge challenge with the planned introduction of Euro VII emissions standard, where stricter CH4 emission limits and a decrease of the cold start starting temperatures are discussed.

During cold start of natural gas engines, increased methane and formaldehyde emissions can be released due to flame quenching on cold cylinder walls, misfiring and the catalyst not being fully active at low temperatures. Euro 6 legislation does not regulate methane and formaldehyde emissions. New limits for these two pollutants have been proposed by CLOVE consortium for Euro 7 scenarios. These proposals indicate tougher requirements for aftertreatment systems of natural gas engines. In the present study, a zero-dimensional model for real-time engine-out emission prediction for transient engine cold start is presented. The model incorporates the stochastic reactor model for spark ignition engines and tabulated chemistry. The tabulated chemistry approach allows to account for the physical and chemical properties of natural gas fuels in detail by using a-priori generated laminar flame speed and combustion chemistry look-up tables.

Spray modelling plays a key role in engine simulations to understand fuel propagation and mixing, combustion, pollutant formation and energy efficiency. The grid dependency, need of calibration of several spray parameters, complexity associated with validation and high computational demand associated with Spray modelling are addressed with 1-dimentional SprayLet model. This work focuses on enhancing the SprayLet model approach with a dual emphasis on computational efficiency and grid independence for advanced engine simulations. Key spray characteristics, such as vapor and liquid penetration lengths, have been systematically evaluated as they play pivotal roles in understanding fuel evaporation, spray-wall interactions, and mixture formation within engines.